Quick Srart Guide

Thank you for purchasing the CNDLive product. Please read this document to familiarize yourself with the unit’s functions. Note that specifications are subject to change without notice.

1. Packing List

Please check that your package contains the following items:

Item	Quantity
Device	1 PCS
Power Adapter	1 PCS
Warranty Card	1 PCS
Quick Start Guide	1 PCS
Certificate	1 PCS

2. Device Interfaces

Hardware Overview

Refer to the diagram below for the physical interface layout.

ID	Component	ID	Component
1	Power Switch	8	HDMI IN
2	Power Port	9	SDI Loop
3	1000M RJ45 Ethernet Port	10	SDI IN
4	Micro SD/TF Slot	11	LCD Screen
5	3.5mm LINE IN/OUT	12	Up Button
6	USB-A Port	13	OK Button
7	HDMI Loop	14	Down Button

Installation & Connection

Connect Signal Source: You can connect both HDMI and SDI sources, or just one.
Connect Network: Connect the Ethernet cable to your working network.
Power On: Use the equipped power adapter to power the device. Turn on the switch button on the panel after setup.

⚠️ Note: If the preview screen is blue or abnormal, check that the source is correctly connected, verify video resolution formats, or change the cable.

3.1 Check IP Address

The device requires a network that supports DHCP. You can find the assigned IP address via the device’s LCD screen:

Press the “Down” button until you see the “Wired Network” information.
Note the IP address displayed (e.g., 192.168.0.16).

3.2 Log in to Web UI

Open a web browser and enter the IP address found in the previous step.
Enter the default credentials below to log in:

Parameter	Default Value
Username	`admin`
Password	`admin`

4. Video Source Selection

By default, the video source is set to HDMI, but you can change this via configuration.

Navigate to Encoding > Video Signal.
Use the dropdown menu to select HDMI, SDI, A mix, or B mix.
Return to the Home page to preview the real-time video of the current encoding source.

5. Streaming Configuration

5.1 Add NDI|HX Stream Service

Click Home on the dashboard, then click Stream Service.
Select NDI|HX in the popup dialog box.
Configure:
- Name/Channel: Fill in the name and channel name.
- Group: Optional (default is “public”).
Click OK to save.
Viewing: Open NDI Studio Monitor (from NDI Tools). Right-click to auto-discover the device and select the configured channel.

5.2 RTMP Live Streaming (YouTube Example)

Click Home > Stream Service and select RTMP/RTMPS.
Get Stream Details: Go to YouTube “Live Video,” enter the live room, and copy the Stream URL and Stream Key.
Configure Encoder: Fill the URL and Stream Key into the encoder’s RTMP push point address.
Start the streaming service to go live.

RTMP Configuration Notes

Format: If the platform separates the RTMP address and Live Broadcast Code (Stream Key), add a / between them (Format: RTMP address/live broadcast code).

Auth: Username and password are usually not required unless the platform explicitly configures the live room with them.

Compatibility: Most platforms can stream directly by default.

6. System Maintenance

6.1 Firmware Update

Click Updating to check for the latest firmware.
If available, select the downloaded firmware and click Firmware Upgrade.
Wait: The upgrade takes approximately 3-5 minutes. The device will reboot automatically upon completion.

⚠️ Warning: Do not power off the device during the upgrade process, as this may cause the device to fail. If the process is not complete after 5 minutes, refresh the webpage.

6.2 Restore Factory Settings

If the device is not functioning normally or you have forgotten the IP configuration, perform a factory reset.

Method 1: Via LCD Screen

On the “State” page, click Enter.
Navigate to System Settings > Down > Reset.
Click Enter to confirm.

Method 2: Via Web UI

Go to Settings > System settings.
Click Restore factory settings.

** Post-Reset Status:**

Username/Password: Resets to admin / admin.

Network: Resets to DHCP mode.

Encoding: All video/audio parameters reset to default values.

7. Support

Email: support@cndlive.com